Category

Category

Basic electrochemical cell setup (redox.me)

This is a stationary solution basic electrochemical cell for measurements of electrodes in a form of:

a) rod/disc (6 mm dia.),

b) thin film deposited on a flat substrate (using a wire clip) and

c) membrane (using a wire clip).

 

The working, counter, and reference electrodes are mounted in a top casing either in 2-, or 3-electrode setup. The cell elements are constructed with materials that are inert to the sample (glass and PEEK). It well fits aqueous (FKM/EPDM O-Rings) and organic solvent (FFKM O-Rings) electrolyte requirements. The construction is gas-tight and can be used when the removal and exclusion of contaminants such as oxygen and water is required by bubbling of an inert gas through the electrolyte. The cell chamber is available in several material variants here (glass, PTFE, PEEK)

 

Application note:
The reference electrode tip should be placed at the level of working electrode center. This will ensure a low potential drop throughout the electrolyte solution for low-current experiment. Various auxiliary electrodes are suitable for this cell including metal wire and metal foil electrodes as well as graphite rod. The bubbling of gas through the solution must be stopped prior to experiment.

 

Specification:
maximum electrolyte volume: 50 mL
electrode plug diameter: 6 mm
number of electrode slots: 3

 

Intrastat data:
HS Code: 90309000
Country of Origin: Sweden
NET weight: 200 g

 

Setup includes:

Item Qty B-A-BEC-50 B-O-BEC-50
BEC 50 mL – Basic Electrochemical Cell 1 C-A-BEC-50 C-O-BEC-50
Metal wire auxiliary electrode – 50HX15 0.6/250 mm, platinum (99,9%), 1 mm dia. gold plated pin 1 E-A-50HX15_Pt-1mm E-O-50HX15_Pt-1mm
Silver / Silver Chloride Reference Electrode – Ag/AgCl 70 mm 1 E-Ag/AgCl_70  
Non-aqueous Silver / Silver Ion Reference Electrode – Ag/Ag+ 70 mm 1   E-Ag/Ag+_70
Working disk electrode – 2 mm dia., PEEK BODY 6 mm dia. – 70 mm, glassy carbon 1 E-A-DISK_GC-70 E-O-DISK_GC-70
10 pcs of Tantalum wire clip with septum plug 0.6 mm dia., 60 mm long 1 E-A-Ta_CLIP-0.6/60-10p E-O-Ta_CLIP-0.6/60-10p

Select configuration

Variant: water based / organic electrolyte

 

 

Categories: , ,

Related products

  • SPE Connector.1 for electrochemical sensors

    The connector enables the use of the biosensor or electrochemical sensor based on the substrates AC1, AC4, AC13 and TS1 1 in classical electrochemical arrangement.

     

    The connector enables measurement with screen printed electrodes with width 7.26 mm and standard contact pads pitch (2.54 mm).
    It is compatible with other SPE´s that use the same distance between the contact pads (2.54 mm). 

     

    Termination: 2 mm Banana plugs

    Read more

  • ZIVE SP1 – potentiostat/galvanostat/ZRA

    • Potentiostat/galvanostat/ZRA at affordable price
    • Control voltage range: ±10V
    • Control current range:9 ranges, 10nA~1A (10nA with gain)

     

    Application

    • Battery
    • Super capacitor
    • Fuel cell
    • Corrosion
    • Sensor
    • Solar cell
    • Other Echem experiments

    Features

    • economical high quality potentiostat/galvanostat/impedance analyzer
    • compact size with full functions
    • ±10V@1Amp control range
    • wide current ranges(1A to 10nA) for various applications
    • built-in FRA : enables EIS tests by using software
    • 14 EIS techniques capability including multisine
    • capable of multitude of applications
      – corrosion, general electrochemistry, sensor, battery, fuel cell,
      supercapacitor, solar cell, etc.
    • bipolar pulse capability
    • voltage pulse or current pulse charge/discharge test(GSM,CDMA etc.),
      sine wave function for ripple simulation withenergysoftwarepackage
      & pulse plating available
    • high speed data sampling time
      – 2usec or 3usec depending on data point number
    • iR compensation and measurement
    • 3 measurement/control voltage ranges &
      9 measurement/control current ranges
    • internal 542,000 data point storage & continuing experiment regardless
      of PC failure.
    • multichannel configuration available
    • free software upgrade

    Experimental Techniques

    Basic techniques

    • Potentiostatic
    • Galvanostatic
    • Double step potentiostatic
    • Double step galvanostatic
    • OCP measurement
    • Potential sweep
    • Current sweep
    • Cyclic voltammetry
    • Fast potential sweep
    • Potentiostatic Ru measurement
    • Galvanostatic Ru measurement

    Advanced Software Package(Included)

    • EIS software package(EISe)
      – Potentiostat EIS
      – Galvanostatic EIS
      – Pseudo galvanostatic EIS
      – OCP* EIS
      – Potentiodynamic PEIS
      – Galvanodynamic GEIS
      – Poteniodynamic HFR
      – Galvanodynamic HFR
      – Potentiostatic HFR monitor
      – Galvanostatic HFR monitor
      – Multisine potentiostatic EIS
      – Multisine galvanostatic EIS
      – Intermittent potentiostatic EIS
      – Intermittent galvanostatic EIS
      (*) The system measures open circuit potential before each frequency
      change and applies AC sine wave on this potential.
    • Corrosion software package(CORe)
      – Tafel(Tafel experiment)
      – Rp(Polarization resistance)
      – RpEc trend
      – PDYN(Potentiodynamic)
      – CYPOL(Cyclic polarization resistance)
      – GDYN(GalvanoDynamic)
      – Reactivation
      – Galvanic corrosion
      – Potentiostatic ECN
      – Galvanostatic ECN
      – ZRA mode ECN
    • Energy software package(BATe)
      a) Battery test technique
      – CC/CV testforcycle life test of lithium battery
      – CC/CC tet forcyclelifetestofNiCd or NiMH battery
      – Discharging test
      – EVS(electrochemical voltage spectroscopy)
      – Variable scan rate CV
      – Potentiostatic IV curve
      – Galvanostatic IV curve
      – Steady state CV
      – PITT(Potentiostatic intermittent titration technique) test
      – GITT(Galvanostatic intermittent titration technique) test
      – Pulse mode is available for GSM & CDMA profile.
      Pulse shape profile can be measured by user’s demand.
      b) Control mode
      – Charge : CC, CC-CV, pulse, sine wave
      – Discharge : CC, CP, CR, pulse, sine wave
      c) Cut-off condition
      – Time, voltage, current, power, auxV etc.
      – Various battery charge/discharge test is available including
      pulse discharge for GSM, CDMA application
    • Electrochemical analysis software package(EASe)
      a) Step techniques
      – CA(Chronoamperometry)
      – CC(Chronocoulometry)
      – CP(Chronopotentiometry)
      b) Sweep techniques
      – LSV(Linear sweep voltammetry)
      – SDV(Sampled DC voltammetry)
      – Fast CV
      – Fast LSV
      c) Pulsed techniques
      – DPV(Differential pulse voltammetry)
      – SWV(Square wave voltammetry)
      – DPA(Diff.pulse amperometry)
      – NPV(Normal pulse voltammetry)
      – RNPV(Reverse normal pulse voltammetry)
      – DNPV(Differential normal pulse voltammetry)
    Read more

  • TC5 Electrochemical Glass Cell

    Borosilicate glass cell serves for electrochemical measurements. The cell is jacketed.

    The analyzed solution can be thermostated by external thermostat.

    Cell openings are designed for electrochemical sensors connector KA1.C, classical electrodes WCEc, ACEc, RCEc and stirrer ST1, ST3 separately.

    Read more

  • Spectro-electrochemical flow cell setup (redox.me)

    This is a horizontally mounted, multi-purpose spectroelectrochemical cell designed to be used with standard UV-Vis or IR spectrometers. It enables obtaining electrochemical and spectroscopic information from liquid sample or thin films in systems where variations in applied potential induce changes in observed spectra. It consists of a polyether ether ketone (PEEK) flow chamber equipped with a magnetic or screw mount sample holder, screw mount quartz window holder and two different mini tripods. It well fits aqueous (FKM O-Rings) and organic solvent (FFKM O-Rings) electrolyte requirements.

    The cell is meant to be used with a standard reference electrode having 6 mm in diameter and a counter electrode either in the form of a rod or helix with 6 mm in diameter and 15 mm active length.

     

    Application note:
    The spectroelectrochemical cell is used to study the relation between absorbance/transmittance and electrochemical potential. It enables real-time monitoring of optical change in electrochromic materials. It also enables in-situ spectral acquisition for detection, identification and characterization of short-lived electrochemically-generated species/intermediates, resulting in a detailed investigation of the mechanistic pathways of redox processes.

     

    Specification:
    nominal exposure area: 1 cm2 (other values on request)
    optical path length (electrolyte thickness): 12 mm
    flow chamber volume: 1.75 mL
    maximum substrate thickness: 4 mm
    electrode plug diameter: 6 mm
    minimum substrate size: 17 mm x 25 mm
    recommended substrate size: 25 mm x 25 mm

     

    Intrastat data:
    HS Code: 90275000
    Country of Origin: Sweden
    NET weight: 300 g

     

    Setup includes:
    1 x Magnetic Mount Spectro-Electrochemical Flow Cell – MM spectro-EFC 1.75 mL (or Spectro-Electrochemical Flow Cell – spectro-EFC 1.75 mL)
    1 x Metal Wire Auxiliary Electrode – 35HX15 0.6/235 mm (Platinum)
    1 x Reference electrode (Ag/AgCl, or Ag/Ag+)

    Read more