TC6 Electrochemical Glass Cell

Related products

• 

  Bottom mount front contact electrochemical cell setup (redox.me)

  This is a static voltammetry cell with variants for different sample dimensions. The sample is loaded from the bottom via magnetic or screw mount, while counter or/and reference electrodes are mounted in the lid as either 2-, or 3-electrode configuration. The cell is constructed with materials that are inert to the sample environment (glass and PEEK), and it can be used with FKM/EPDM O-rings or FFKM O-rings for aqueous or organic electrolyte requirements, respectively. The construction is gas-tight and inert gas can be bubbled through the electrolyte to remove and exclude contaminants such as air or water.

   

  Application note:
  The reference electrode tip should be placed close to the sample surface to ensure a negligible potential drop throughout the electrolyte solution during low-current experiments. In the magnetic variant of the cell, the strength with which the magnets hold the sample is adjusted by adding or removing the washers under the magnets. Thanks to this procedure, the distance between the magnets changes, with it, the force of their attraction. Various auxiliary electrodes are suitable for this cell, including metal wire and metal plate electrodes as well as carbon-based electrodes (graphite or Glassy Carbon). If a purge gas is used, stop the flow during experiments for better results. 

   

  Specification:
  nominal exposure area: 0.07 cm² for 5x5mm², 0.2 cm² for 7x7mm², 0.5 cm² for 10x10mm², and 1.33 cm² for 15x15mm²
  minimum electrolyte volume: 2.5 mL
  maximum electrolyte volume: 15 mL
  electrode plug diameter: 6 mm
  substrate size: 5x5mm², 7x7mm², 10x10mm², and 15x15mm², other sizes available on request
  minimum substrate thickness: 0.4 mm*

  *lower thicknesses are also feasible when using a pad below the sample

   

  Intrastat data:
  HS Code: 90309000
  Country of Origin: Sweden
  NET weight: 200 g

   

  Setup includes:
  1 x BM FC EC 15mL – Bottom Mount Front Contact Electrochemical Cell, 15mL (or BMM FC EC 15mL – Bottom Magnetic Mount Front Contact Electrochemical Cell, 15mL)
        1 x lid
        1 x glass chamber
        1 x bottom casing
        1 x sample mount
        1 x tantalum contact
        1 x plug
        1 x set of Nylon screws (screw variant only)
  1 x Reference electrode (Ag/AgCl, or Ag/Ag+), 70mm, 4 mm female banana socket
  1 x Metal Wire Auxiliary Electrode – 50HX15 0.6/250 mm, platinum 99.9%, 4 mm female banana socket

  Read more
• 

  TC7 Electrochemical Glass Cell

  The TC7 is a low cost Glass Cell that is ideal for students and basic lab measurements.

   

  The TC7 comes with a stand, specially designed for it, and the stand provides more stability and ease of use.

  The Borosilicate glass cell serves for electrochemical measurements. Cell openings are designed for the SPE Electrochemical Sensors Connector KA1.C,Classical Electrodes WCEc, ACEc, RCEc, STP1.*

  Stoppers for Cells, and Stirrer’s ST1 and ST3 separately.

  The device enables the measurement with inserted samples.

  Read more
• 

  Basic electrochemical cell setup (redox.me)

  This is a stationary solution basic electrochemical cell for measurements of electrodes in a form of:

  a) rod/disc (6 mm dia.),

  b) thin film deposited on a flat substrate (using a wire clip) and

  c) membrane (using a wire clip).

   

  The working, counter, and reference electrodes are mounted in a top casing either in 2-, or 3-electrode setup. The cell elements are constructed with materials that are inert to the sample (glass and PEEK). It well fits aqueous (FKM/EPDM O-Rings) and organic solvent (FFKM O-Rings) electrolyte requirements. The construction is gas-tight and can be used when the removal and exclusion of contaminants such as oxygen and water is required by bubbling of an inert gas through the electrolyte. The cell chamber is available in several material variants here (glass, PTFE, PEEK)

   

  Application note:
  The reference electrode tip should be placed at the level of working electrode center. This will ensure a low potential drop throughout the electrolyte solution for low-current experiment. Various auxiliary electrodes are suitable for this cell including metal wire and metal foil electrodes as well as graphite rod. The bubbling of gas through the solution must be stopped prior to experiment.

   

  Specification:
  maximum electrolyte volume: 50 mL
  electrode plug diameter: 6 mm
  number of electrode slots: 3

   

  Intrastat data:
  HS Code: 90309000
  Country of Origin: Sweden
  NET weight: 200 g

   

  Setup includes:

  Item	Qty	B-A-BEC-50	B-O-BEC-50
  BEC 50 mL – Basic Electrochemical Cell	1	C-A-BEC-50	C-O-BEC-50
  Metal wire auxiliary electrode – 50HX15 0.6/250 mm, platinum (99,9%), 1 mm dia. gold plated pin	1	E-A-50HX15_Pt-1mm	E-O-50HX15_Pt-1mm
  Silver / Silver Chloride Reference Electrode – Ag/AgCl 70 mm	1	E-Ag/AgCl_70
  Non-aqueous Silver / Silver Ion Reference Electrode – Ag/Ag+ 70 mm	1		E-Ag/Ag+_70
  Working disk electrode – 2 mm dia., PEEK BODY 6 mm dia. – 70 mm, glassy carbon	1	E-A-DISK_GC-70	E-O-DISK_GC-70
  10 pcs of Tantalum wire clip with septum plug 0.6 mm dia., 60 mm long	1	E-A-Ta_CLIP-0.6/60-10p	E-O-Ta_CLIP-0.6/60-10p

  Read more
• 

  Standard electrochemical cell setup (redox.me)

  This is a stationary solution standard electrochemical (electrolytic) cell for measurements of electrodes in a form of:

  a) rod/disc (6 mm dia.),

  b) thin film deposited on a flat substrate (using a sample holder) and

  c) free-standing membrane (using the basic sample holder).

   

  The working, counter, and reference electrodes are mounted in a top casing either in 2-, or 3-electrode setup. The cell has two spare ports for connection of e.g. thermometer, Clark electrode, pH meter electrode, or other 6 mm dia. electrode/probe. 

  The cell elements are constructed with materials that are inert to the sample (glass and PEEK). It well fits aqueous (EPDM O-Rings) and organic solvent (FFKM O-Rings) electrolyte requirements. The construction is gas-tight and can be used when the removal and exclusion of contaminants such as oxygen and water is required by bubbling of an inert gas through the electrolyte. The jacketed model is available here. 

   

  Application note
  The reference electrode tip should be placed close to a working electrode center. This will ensure a low potential drop throughout the electrolyte solution for low-current experiment. Various auxiliary electrodes are suitable for this cell including metal wire and metal foil electrodes as well as graphite rod. The bubbling of gas through the solution must be stopped prior to experiment.

   

  Specification:
  maximum electrolyte volume: 100, 150, 200, 250, 350, 500 or 1000 mL
  electrode plug diameter: 6 mm
  number of electrode ports: 5
  vial material: borosilicate 3.3 glass

   

  Intrastat data:
  HS Code: 90309000
  Country of Origin: Sweden
  NET weight: 200 g (100, 150 mL), 300 g (200, 250, 350 mL), 400 g (500 mL), 600 g (1000 mL)

   

   

  Read more