Mini *-ISE-L60.C* Miniature ion selective elecrodes

You may also like…

• 

  ISE Ion Selective Electrodes

  Ion Selective Electrodes, ISEs, are analytical tools widely used for potentiometric analysis of large scale of various ionic analytes.

   

  ISEs enable routine analysis in agriculture, food process, soil analysis, environmental anylysis, tribotechnical analysis, explosives and pyrotechnical mixtures analysis. They can be used for water, pot-, waste-, boiler-, mineral-, and well water samples.

   

  These electrodes allow for direct measurements of Ammonium, Lithium, Sodium, Calcium, Fluoride, Nitrate, Potassium and Barium.

   

  Electrodes are applicable to all commonly used measuring apparatus, with internal resistance of above 10^9 – 10^12 ohm.

  Diameter: 12 mm.

  Standard electrical connecting cable is 0.8 to 1 m. coaxial cable with BNC connector.

  The work with ion selective electrodes is time effective, requires an only small amount of chemicals, and a friendly price of measuring equipment MPH472.

  Read more
• 

  FC.1ISE.1REF Flow cell for single ion selective electrode with integrated stirring

  The flow cell with integrated stirring and reduced hydrodynamic noise is designed for the determination of single analyte using one miniature ion-selective electrode (ISE) and one miniature reference electrode with a diameter of 6 mm and length of 60 mm.

   

  Rotation speed of integrated stirrer: 10-4000 rmp.

   

  Miniature ion-selective electrodes and reference electrode were designed for integration into the flow cell for determination of Cl-, K+, Ca2+ and Na+ ions.

   

  In flow mode, the system can operate automatically. The speed of the integrated stirrer can also be controlled by applying the corresponding voltage to the motor, connected to a stabilized source.

   

  The flow cell with one selected ISE can be used for:

  • Automatic or semi-automatic measurement of concentration of Cl-, K+, Ca2+ and Na+ ions in various solutions (following prior calibration)
  • For continuous measurement of changes in concentration of Cl-, K+, Ca2+ and Na+ ions.

   

   

  * For this product, we recommend our customers use the Training Service from BVT.

  (https://bvt.cz/produkt/offer-of-long-term-automated-measurements-on-bvt-apparatus/)

  Read more
• 

  Mini RCE.GEL.L60.C1 Miniature reference argentochloride gel electrode

  Miniature reference argentochloride gel electrode is designed for potentiometric measurements in connection with Miniature ion selective electrodes for potentiometric measurements of Chloride ions, Sodium ions, Calcium and Potassium ions concentration in aqueous solutions following prior calibration.

   

  The conductive connection of the internal electrolyte (KCl gel) enclosed in a plastic tube is mediated by a porous frit.

  Maintenance-free electrode – no need to top up the internal electrolyte (KCl gel).

   

  Electrodes are applicable to all commonly used measuring apparatus, with input resistance of at least 1012 Ω.

   

  Possibility of integration with a FC.1ISE.1REF Flow cell for single ion selective electrode with integrated stirring – possible automation and continuous measurement.

  Read more
• 

  MPH 472 Universal Potentiostat

  The instrument enables measurement of amperometry, potentiometry and conductometry. Communication with the computer is provided via USB or Bluetooth. This hand-held device is equipped with GPS navigation so the measured data may be enhanced by the exact coordinates of the location where the measurement was made.

   

  Measured data can be stored and later processed in a PC because of the SD card slot incorporation. The ability to record a waveforms or integrate the measure values is enabled. Basic evaluation methods are also implemented – linear and non-linear calibration and standard addition method is available. The influence of the type of oxygen electrode membrane, temperature or gas solubility can be compensated for the measured values.

   

  The measured data are automatically recalculated and displayed in units of current, voltage, concentration (g∙L-1 or mol∙L-1) or saturation. Potentiometric measurement allows connection of pH electrodes and ISE.

   

  Key Properties

  • Up to 200 hours of battery life depending on the operating mode.
  • Excellent analytical tools (graphs, unit conversions, internal standard method for potentiometry, coulometric titration, 10 Henry’s constants for various redox active gases).
  • Power supply and data communication via USB, possibility of connection via Bluetooth.
  • Data logging to memory card.
  • Up to 5-point calibration for ISE and pH electrodes.
  • Up to 4-point calibration of the conductivity cell makes it possible to compensate the non-linearity of the measurement.
  • GPS equipment enables measurements in the field with location storage.
  • Calibration stored separately in the device (possibility of changing the memory card without having to recalibrate the device).
  • Possibility of separate calibration for 4 probes for amperometry and potentiometry.
  • The possibility of using different temperature sensors (PT100, PT1000, Ni1000, ATC Monocrystals).
  • Advanced power management (display sleep and automatic device shutdown can be set according to the user’s preferences
  • Vector voltmeter for accurate conductivity measurement.
  • Powerful thirty-two-bit microprocessor for accurate measurement calculations.

  Improvements:

  • Faster battery charging via USB charger.
  • Vector voltmeter for precise conductometric measurement.
  • A more sensitive GPS module.
  • More robust input circuits for ametrometric measurement –  less susceptible to noise.

   

  More information can be found through the link: https://www.monokrystaly.cz/cs/ph-mv-ion-metry.html?fbclid=IwAR3ieir-mH-D10LZ-SZkrx74OHZYvOHjZPnOX8nfi9WdcwostsUgTAVaZPM#MPH471 

   

  Read more