Category

Category

SPE Connector.GC.1 for measurements in glass

The connector enables the use of the biosensor or electrochemical sensor based on the substrates AC1, AC4 and TS1 in glass cell TC4, TC5, TC6 or TC7.

 

The connector enables measurement with screen printed electrodes with width 7.26 mm and standard contact pads pitch (2.54 mm).
It is compatible with other SPE´s that use the same distance between the contact pads (2.54 mm). The cone at the connector sensor side is NJ 8/10 which enables to use the connector with any standard chemical vessels.

 

Termination: 2 mm Banana plugs

Useful Documents

SPE Connector.GC.1 Datasheet

Connector quality and its effects on measurements with Screen Printed Electrodes sensors (SPE)

Categories: ,

You may also like…

  • AC1 Dwe= 1mm, 2 mm Electrochemical sensor

    Basic amperometric low cost three-electrode sensor with patented structure made by thick film technology.  

    Dimensions: 25.4 x 7.26 x 0.63 mm

    WE material: Au/Pt, Au, Pt, Ag, C

     

    The sensor is formed on a corundum ceramic base. On to this surface the working, the reference and the auxiliary electrodes are applied. The working and the auxiliary electrodes are made of variety of materials. At the end of the sensor there is a contacting field which is connected with the active part by the silver conducting paths which are covered by a dielectric protection layer.

     

    A bio-chemically active substance can be immobilised on the working electrode of the sensor to create a biosensor. All sensors can be equipped with heating and temperature sensing elements. Thermistor (must be calibrated) or Pt 1000 (the response corresponds to the ISO standard) is used as the temperature sensor.

     

     

    We also offer:

    • working electrode made of polished gold (WE diameter 1 or 2 mm) – sensor type: AC1P.W*.R*, with homogenous surface with roughness less than 1 µm
    • working electrode made of a material of guaranteed purity of up to 99.99 % (WE diameter 2 mm) – sensor type: AC1.GP

    We also offer activated graphite sensors on customer request.

    See activation example below:

     

    * Have a look at product cathegory Discounted SPEs – which include offer of Screen Printed Electrodes (SPEs) at a reduced Price from our AC1 line of Sensors. They are fully functional, but with visual defects or inconsistancies.

    – ideal for use by students to gain handling experience and knowledge on SPEs and their uses
    – ideal for initial experiments in research

    Read more

  • TC6 Electrochemical Glass Cell

    Borosilicate glass cell serves for electrochemical measurements.

     

    The analyzed solution can be thermostated by minithermostat MT1-1.

     

    Cell openings are designed for electrochemical sensors connector KA1.C, classical electrodes WCEc, ACEc, RCEc and stirrer ST1, ST3 separately.

     

    The device enables the measurement with inserted samples.

    Read more

  • CC1 Electrochemical sensor

    A conductivity sensor made by thick film technology with interdigitated structure of electrodes

    Dimensions: 25.4 x 7.26 x 0.63 mm

    WE material: Au/Pt, Au, Pt, Ag, C

     

    The sensor is formed on a corundum ceramic base. Onto this surface two interdigitated structures of electrodes are applied. The electrodes are made of Platinum-Gold alloy in standard product CC1.WS. At the end of the sensor there is a contact which is connected with the active part by the silver conducting path which is covered by a dielectric protection layer. A bio-chemically active substance can be immobilised on the working electrode of the sensor.

    Read more

Related products

  • KA1.C.* Conic Connector for Electrochemical Sensors

    The connector enables the use of the biosensor based on the substrates AC1, AC4, AC11, AC13, CC1, CC2 and TS1 in classical electrochemical arrangement with stirred vessel. The cell TC4, TC5, TC6 is recommended for use with KA1.C.*.

    Read more

  • EmStat4 MUX (2-in-1: Potentiostat with integrated multiplexer)

    Gone are the days with too many cables. With the EmStat4 MUX you have a potentiostat and a multiplexer in one! The EmStat4 MUX is a powerful potentiostat, galvanostat and impedance analyzer and supports all popular electrochemical techniques. Its 8 channels allow for sequential measurements, for example eight Screen-printed electrodes, or eight working electrodes in eight different  cells.  The instrument’s measurements can be highly customized using MethodSCRIPT. The 4 different cell connections available allow for many different setups. When the measurements are finished, you can easily save your results in PSTrace, or export your results to Excel. 

     

    More information could be found tought link:

    https://www.palmsens.com/product/emstat4-mux/

     

    • Integrated 8-channel multiplexer
    • Supports 2-, 3- and 4-electrode setup using Sense Lead
    • Potential range: ± 3V 
    • Compliance voltage: ± 5V
    • Current ranges:  1 nA – 10 mA
    • Maximum current: ± 30 mA
    • FRA / EIS up to 200 kHz

    Two modes of operation

    • Consecutive mode: this mode switches channel when a complete measurement has finished
    • Alternate mode: this mode switches all activated channels within the specified time interval of a measurement.

    In both modes the unselected Working Electrodes can either be left floating or switched to Ground to keep the specified voltage.

    Supports a 2-, 3- or 4-electrode setup

    • Connect four electrodes per channel by using the Sense Leads. 
    • Or connect only three electrodes per channel by internally connecting all Sense electrodes to the Working Electodes in software.
    • Do you need to connect only two electrodes per channel? Combine the reference and counter electrode physically on the cable, or with a single click on the PSTrace software.

    8 to 128 channels

    Is 8 channels not enough? If more channels are required, one or more MUX-R2 can be stacked to the EmStat4 MUX for a total of up to 128 channels.

    Script your experiments!

    Via the script window of PSTrace it is possible to perform a different experiment on each of the channels sequentially. Alternatively, you can use MethodSCRIPT to fully customize your measurements per channel.

    Multichannel or Multiplexer?

    To make it easier for you to decide, if  a multiplexer or a multichannel device is more suitable for your application, we have created a short explanation of multiplexers and multichannels.

    See: https://www.palmsens.com/app/uploads/2016/12/Multiplexer-Polypotentiostat-or-Multichannel.pdf

     

    Read more

  • USB Potentiostat Galvanoplot

    USB Potentiostat Galvanoplot is a super small, low-cost and affordable device suitable for dedicated volume applications, which is optimized for screen-printed sensor and biosensor applications. It can be used in many other research areas and with other electrochemical sensors, for corrosion measurement, battery and super-capacitors or fuel cells.

    It is capable of performing all common Amperometric and Voltammetric electrochemistry protocols (CA, LSV, CV, DPV, NPV, SVW, GAL) and can be used with three electrode (WE/RE/CE) and two electrode (WE/RE-CE) setups. Plug the device directly into an Android mobile device through OTG port for a true on-site analysis experience. It is possible to choose from two types of interfaces allowing direct insertion of the BVT SPE sensors or the use of 3 classical electrodes with 2 mm banana plugs (WE, RE, CE).

     

    Specifications

    • Dimensions: 39x17x8 mm
    • Weight: 5 g without sensor interface
    • Voltage scan range: +-3V @1mV resolution 
    • Max current: 2000 nA (*at the request of the customer, it is possible to change the range, but this will change the resolution, noise and other parameters)
    • Current resolution: 300pA@1KSPS/ 100pA@100SPS/ 30pA/10 SPS resolution
    • Noise around: 50nA@1KSPS/ 7nA@100SPS/ 400pA/10 SPS

     

    • Protocols: CA, LSV, CV, DPV, NPV, SVW, GAL
    • Cell type: WE/RE/CE and WE/RE-CE
      Connectivity: USB-C (Plug the device directly into an Android mobile device through OTG port for a true on-site analysis experience)

     

    • Operating system compatibility: Windows 8, 10+
    • Advanced analysis – filtering and auto peaks

     

    Device Usage

    • Electrochemical measurements
    • Measurements with biosensors and electrochemical sensors
    • Measurement of biochemical activity of a sample
    • Corrosion measurement

     

    Read more

  • KA1.S.* Simple Connector for Electrochemical Sensors

    The connector enables the use of the biosensor based on the substrates AC1, AC4, AC11, AC13, CC1, CC2 and TS1 in classical electrochemical arrangement with stirred vessel.

    Read more